C2206 Vehicle Configuration Mismatch

C2206 Code  - when the Anti-Lock Brake System (ABS) Module detects the signal from the gateway module relevant for vehicle charac…

C2204 Dynamics Sensor Internal

C2204 Code  - Ignition on, no under voltage DTCs. Until vehicle speed exceeds 20 km/h (12.4 mph) for the first time. If DTC U1003…

C2200 Anti-lock Brake Module Internal

C2200 Code  - ignition on. The Antilock Brake Module (ABS) monitors its internal microprocessors for correct operation. If the An…

C1240 Steering Angle Sensor Overtravel Performance

C1240 Code  - with ignition on, but not if a CAN time out failure is detected. Or, if a fault is detected by the Steering Angle S…

C1239 Emission Rolls Test Active

C1239 Code  - continuously with the ignition on and the Totally Intergrated Power Module has the emissions test mode bit set. If …

C1091 Code | ABS Brake Lamp Control Circuit High

C1091 Code  - the Electronic Stability Control (ESC) may also be refferd to as Electronic Stability Program (ESP) depending on th…

C1234 Drive Test: Sensor Cluster Installation

When monitored code C1234 - During the drive test. Set condition, if the Antilock Brake System (ABS) Module detects implausible …

C1232 Drive Test: Pressure Sensor

C1232 code - During the drive test. Set condition, if the pressure sensor fails to activate. Possible causes code C1232 Dr…

C1231 Drive Test: Steering Angle Sensor

C1231 Drive Test: Steering Angle Sensor - When monitored code C1231 drive test: steering angle sensor, during the drive test. Se…

C1238 Drive Test: Unsuccessful

C1238 Drive Test: Unsuccessful - If any other DTCs are present, repair them first before continuing with this diagnostic procedu…

C1219 Steering Angle Sensor Erratic Performance

C1219 code - Steering angle sensor erratic performance, continuous monitoring. Set condition code C1219, if the Antilock Brake S…

C1210 G Sensor Input Circuit Performance

When monitored code C1210 G sensor input circuit performance Continuously, with ignition on, until vehicle speed exceeds 20 km/h…

C1090 ABS Brake Lamp Control Circuit Low

C1090 ABS Brake Lamp Control Circuit Low - The Electronic Stability Control (ESC) may also be reffered to as Electronic Stabilit…

C1085 Vacuum Pressure Sensor High

C1085 Vacuum Pressure Sensor High - The vacuum sensor signal indicates thta the voltage level is below 0.1 volt or greater than …

C1084 Vacuum Pressure Sensor Low

C1084 Vacuum Pressure Sensor Low - The vacuum sensor signal indicates thta the voltage level is below 0.1 volt or greater than 3.…

C1083 Vacuum Pressure Sensor Performance

C1083 Vacuum Pressure Sensor Performance - When the Antilock Brake System Module detects that the vacuum sensor signal does not …

C102A JEEP, DODGE Left Rear Wheel Speed Comparative Performance

C102A JEEP, DODGE - When the Left Rear Wheel Speed Sensor (WSS) reading is difeerent from the readings received from the other s…

C121A-00 DODGE, CHRYSLER 300 Steering Angle Sensor Not Initialized

C121A-00 Steering angle sensor not initialized The Steering Angle Sensor (SAS) has not been properly initialized. Possible ca…

C121A-09 DODGE, CHRYSLER 300 Steering Angle Sensor Not Initialized - Component Failure

C121A-09 DODGE, CHRYSLER 300 Steering Angle Sensor Not Initialized - Component Failure. Repair any Steering Control Module (SCM) …

C2116 JEEP, DODGE, CHRYSLER ABS Pump Supply Low Voltage

C2116 Code -  The Electronic Stability Control (ESC) may also be referred to as Electronic Stability Program (ESP) depending on t…